**SHIPPING NOT INCLUDED IN PRICING**

*Disassembly/Reassembly Charges of $50-$100 are in addition to work performed.*

General Shop Services

Labor rate for non flat rate work: $100/hr, $50 minimum

Machine time for non flat rate work: $150/hr, $75 minimum

Sight in: $125 + ammo cost

Scope Installation: $50 + parts

General Barrel Services

**Turn around time for muzzle work/threading is 2-3 weeks.**

Threading prices are for barreled actions or barrels only! There will be an additional disassembly charge of $50-$100 for complete firearms.

Muzzle Threading- Standard shoulder: $150

Muzzle Threading- Q Taper: $175.00

Muzzle Threading with Flared Shoulder: $200

Muzzle Threading with Permanent adapter: $250

Muzzle Threading- Fluted barrel: Includes blending flutes. See Below

• Tikka Superlite 1/2-28 or 9/16-24: $250 + Refinish

• Tikka Superlite 5/8-24: $300 + Refinish

• Other Fluted Barrel: POR

Time/Install Aftermarket Brake (standalone): $100.00

Time/Install Aftermarket Brake (paired w/ muzzle threading): $50

Cut and Crown Barrel: $75.00

Cut Dovetail: $75 Set up, $75 per dovetail

Drill/Tap: $75 Set up, $25/hole

Pin and Weld: $100

Install Barrel Band Sling Stud: $250 + refinish, parts included

Shop Made Muzzle Brake

• Chrome-moly/Stainless: $175.00
• Titanium: $215.00
• Includes timing and profiling
• Does not include refinishing

Thread Protector:

• Stainless contour matched but NOT blended: $50
• Blended/ Seamless: $75 + Barrel refinishing

Bolt Action Services

Receiver/ Bolt Truing: $350.00

• Receiver face, locking lugs, receiver threads are single point cut to be concentric and perpendicular to the bolt raceway.
• Bolt face and lugs single point cut.
• Precision ground recoil lug not included.

Fit and Chamber Barrel: $450.00 + Barrel Cost

• Class 3 thread fit.
• Cut and polished chamber.
• Cut barrel to length and crown.
• Add extractor groove for $100.00

Action Bedding: $200

• Stress free epoxy bedding.
• Free float barrel.

Pillar Bedding: $250

• Same as above with added aluminum pillars.

Install Pre-fit Barrel: $150

• Includes verifying headspace.

Install Threaded Stud for Aftermarket Bolt Knob: $150

• 5/16-24 thread standard.

Install Aftermarket Trigger: $100

Scope Mounting: $50

• Does not include cost of rings or bases.

Lever Action Muzzle Threading: $300.00

• Shorten magazine tube as necessary.
• Move front sight as necessary.
• Includes thread protector.
• Works on most makes and models.

Internal Muzzle Threading: $400

• Allows use of full length magazine tube
• No need to move front sight in most cases.
• Thread protector and thread adapter included.

Henry Magazine Tube Conversion: $200.00

• Converts unsightly factory mag tube to traditional style.
• Includes Cerakote or blued finish.
• Requires a factory sidegate.

Receiver/Bolt Truing: $250.00 (Requires additional barrel work)

• Receiver face single point cut perpendicular to bolt raceway.
• Threads re-cut if necessary.
• Bolt face single point cut perpendicular to body.

Non-Standard Cartridge Conversion (480 Ruger, 10mm, 45ACP, 50 Alaskan, etc..) Starting at $2,000

Fit/Chamber Barrel Blank: $750.00 + Barrel Cost

• Class 3 thread fit.
• Cut and polished chamber.
• Cut barrel to length and crown.
• Includes any chamber hoods and extractor groove needed.
• Includes necessary magazine tube clearance cuts and dovetails.
• Includes necessary sight dovetails/mounting holes.
• Add muzzle threads for $100.00
• Add Bluing for $125

Polish/Tune Internals: $200

• Includes trigger job, correcting timing, correcting hammer drag.

Drill and Tap for Receiver Sight or Scope: $75 Setup, $25.00 per hole.

Single Shot Services

Ruger No. 1- Fit and Chamber Barrel: $650 + Barrel Cost

• Cut and polish chamber
• Cut clearance for ejector
• Install factory rib or scope blocks
• Install factory sights
• Add bluing for $125

Accurize Ruger No. 1: $300

• Fire test group before and after work performed.
• Bed forend to receiver and spring hanger
• Cut clearance between scope rib and receiver

Break Action Barrel Stub: POR

Stock Services

Install Sling Studs: $25.00/stud, studs not included.

Install Recoil Pad: $200, Includes pad of your choice.

Inletting: Hourly rate

Repair Cracked/Broken Stock: POR

Refinish Wood Stock: Starting at $400.00

Refinish Painted Stock: POR

Spray Coatings

Cerakote and KG Gunkote Available.

Barreled Action (Bolt Action or Single Shot): $250.00 + dis/reassembly

Lever Action Single Color (Metal Parts): $350.00 + dis/reassembly

Stock Single Color: $175

Battleworn: + $50

2 Color Camo: + $100

3 Color Camo: +$200

NO KRYPTEK, MULTICAM, HEX, DIGITAL, SITKA, ETC..

Metal Finishing

Hot Bluing: POR

Rust Bluing: POR

Bead Blasting/Brushed Stainless: $150 + Dis/Reassembly

Bolt Jeweling: $150

Laser Engraving

NFA Engraving: $50.00

• Engraved to NFA requirements for size and depth

Personalized Text/Script: $50.00

Scope Cap Engraving; $100.00

• Your DOPE engraved for your specific load data.